amd100 e, Alarmy, domofony, P.Poż, Satel
[ Pobierz całość w formacie PDF ]
®
WIRELESS MAGNETIC DETECTOR
AMD-100
amd100_e 09/05
The AMD-100 wireless magnetic detector is designed for operation as part of the
ABAX two-way wireless system.
The AMD-100 detector is of the NC type, i.e. moving the
magnet away from the reed relay opens the electric circuit,
which is recognized as violation of the detector.
Descriptions of Figure 1:
1 – additional input terminals - The NC type detector can be
connected to them The additional input is connected in
series with the reed switches on the electronics board.
2 – tamper contact – It reacts to opening or pull-off of the
housing from the wall.
3 – CR123A lithium battery (voltage: 3V), which ensures
approx. two years’ operation.
4 – reed switch 1.
5 – reed switch 2.
6 – pins which enables to choose the active reed switch.
active reed switch 1
active reed switch 2
Fig. 1. View of the
detector PCB.
Fig. 2. The way of putting jumper on pins.
7 – LED indicator – is on in the
T
EST MODE
only (see the ACU-100 controller manual)
to signal communication with the controller and violation (of the detector or
tamper contact).
Placed on the electronics board is a label with 7-digit serial number, which must be
indicated when registering the detector in the system.
1. D
ETECTOR INSTALLATION
Prior to permanent mounting of the detector, you should check the level of
signal received from the detector by the ACU-100 controller and, if necessary,
change place of the installation so as to ensure optimal positioning in terms of
communication.
Place the battery inside the detector immediately before registering the detector
in the controller. If not registered or lacking communication with the controller,
the detector consumes more energy, which reduces the battery lifetime.
Be particularly careful when installing or replacing the battery, so as not to
damage the reed switches on the electronics board.
2
SATEL
AMD-100
The cable connecting the additional detector with the onboard terminals may not be
longer than 3m. If the additional input is unused, its contacts should be shorted.
For information on registration and installation of the detector in the wireless system -
see the ACU-100 controller user manual.
Side view
reed switches
tamper contact spring
17mm
Top view
reed switches
110mm
Fig. 3. View of AMD-100 in the housing with indicated position of
reed switches.
magnet
reed switch
reed switch
reed switch
20mm
Fig. 4. Examples of mounting reed switch and magnet, showing the maximum ranges
(top view). The indicated ranges apply to the magnet situated at the height of
AMD-100 PCB.
AMD-100
ABAX
3
2. T
ECHNICAL DATA
Detector type ..............................................................................................................NC
Operating frequency band .......................................................... 868.0MHz ÷ 868.6MHz
Additional input sensitivity .................................................................................... 312ms
Power supply .........................................................................lithium battery CR123A 3V
Lifetime of detector power battery .......................................................... approx. 2 years
Operating temperature range .......................................................................0°C...+55°C
Dimensions of reed relay housing ........................................................... 24x110x27mm
Batteries in the battery-supplied wireless equipment should be replaced by
qualified personnel. Incorrect replacement of the battery can pose an explosion
hazard.
Always use the CR123A 3V lithium batteries.
The used batteries must not be discarded, but should be disposed of in
accordance with the existing rules for environment protection.
DECLARATION OF CONFORMITY
Manufacturer:
SATEL spółka z o.o.
ul. Schuberta 79
80-172 Gdańsk, POLAND
tel. (+48 58) 320-94-00
fax. (+48 58) 320-94-01
Product description
:
Wireless magnetic detector designed for interaction with elements of the
ABAX wireless system, operating in the 868.0MHz – 868.6MHz frequency band, supplied from a 3V
lithium cell. The device is intended to be used in burglary and panic alarm systems.
This product conforms to the following EU Directives:
R&TTE
1999/5/EC
This product meets requirements of the harmonized standards:
R&TTE: ETSI EN 300 220-1: v.1.3.1; ETSI EN 300 220-3: v.1.1.1;
EMC: ETSI EN 301 489-1: v.1.5.1.; EN 301 489-3: v.1.4.1
Safety: EN60950-1:2001
Notified body taking part in conformity evaluation:
Identification No.: 1471
Head of Test Laboratory:
Michał Konarski
The latest EC declaration of conformity and product approval certificates are available for
downloading on website
www.satel.pl
Gdańsk, Poland 2005-07-15
Product:
AMD-100 - Wireless Magnetic Detector for
ABAX System
4
SATEL
AMD-100
SATEL sp. z o.o.
ul. Schuberta 79
80-172 Gdańsk
POLAND
tel. + 48 58 320 94 00
info@satel.pl
www.satel.pl
[ Pobierz całość w formacie PDF ]